Expert HVAC solutions for homes and businesses across Highland Park, TX. Certified technicians, transparent pricing, and results you can count on.
Browse our full range of heating, cooling, and air quality services available in your area.
Seasonal air conditioning maintenance prevents costly mid-summer failures by verifying refrigerant charge, cleaning condenser coils, and testing capacitor microfarad ratings against manufacturer tolerances. A thorough tune-up preserves SEER efficiency and extends compressor lifespan by reducing operational strain.
Ductwork problems manifest as uneven room temperatures, excessive dust near registers, and HVAC systems that run continuously without satisfying the thermostat. Technicians identify crushed flex runs, separated joints, and deteriorated mastic seals using pressure testing and visual inspection protocols.
Boiler systems demand specialized knowledge of hydronic circuits, expansion tanks, pressure relief valves, and combustion analysis. Our technicians diagnose issues ranging from kettling and low water pressure to faulty zone valves and circulator pump failures across gas, oil, and electric units.
Heat pumps rely on a precise balance of refrigerant pressure, electrical components, and airflow to deliver efficient heating and cooling year-round. Professional repair addresses compressor hard starts, frozen coils, faulty thermostatic expansion valves, and auxiliary heat lockout conditions.
Clean ductwork directly impacts the efficiency of your HVAC system by reducing static pressure and allowing unrestricted airflow to every register. Our technicians inspect for microbial growth, seal access points after service, and verify airflow improvements with anemometer readings post-cleaning.
Upgrading to a modern heat pump delivers dual-mode heating and cooling from a single system, with top-tier models achieving 10+ HSPF and 20+ SEER2 ratings. Proper installation includes Manual J load calculations, refrigerant line sizing, and electrical panel verification for reliable year-round comfort.
Full HVAC installation requires coordination of heating equipment, cooling components, ductwork design, and control systems to deliver efficient comfort at rated capacity. Our technicians perform Manual J and Manual D calculations, size equipment to match your structure, and commission the system to manufacturer standards.
A professionally installed mini-split eliminates the energy losses associated with traditional ductwork while providing independent temperature control per zone. Technicians mount indoor heads at optimal height, route linesets with proper insulation, and commission each zone for verified heating and cooling output.
When a mini-split displays error codes, produces weak airflow, or fails to reach setpoint, the fault often lies within the inverter board, thermistor sensors, or refrigerant circuit. Professional repair restores rated SEER output and eliminates the inefficient short cycling that drives up utility costs.
A comprehensive furnace tune-up includes combustion analysis, heat exchanger inspection, and verification of gas pressure at the manifold. Technicians clean burners, test flame sensor microamp readings, and confirm proper flue draft to maintain safe, efficient operation throughout the heating season.
Restoring reliable air conditioning performance requires more than replacing visible parts. Technicians measure refrigerant pressures, check compressor winding resistance, test run and start capacitors, and verify condenser fan operation to ensure every component of the cooling circuit functions within specification.
Comprehensive HVAC inspections cover thermostat operation, ductwork condition, refrigerant levels, electrical connections, and combustion safety. This detailed assessment identifies efficiency losses, safety hazards, and components nearing end of service life before they result in costly emergency repairs.
Upgrading to a smart thermostat enables precise scheduling, remote access, and energy usage reporting that can reduce heating and cooling costs by 10 to 15 percent. Professional installation ensures correct wiring to your HVAC system, including C-wire verification and multi-stage equipment compatibility.
Sudden HVAC failures often stem from compressor lockout, blown transformer fuses, failed gas valves, or tripped high-pressure switches. Emergency repair service provides same-day response with technicians equipped to diagnose and resolve critical faults across all major heating and cooling equipment brands.
A dryer that takes multiple cycles to dry clothes or feels excessively hot to the touch signals a restricted vent line. Technicians clear lint accumulation using rotary brush systems and compressed air, then verify exhaust velocity meets manufacturer specifications for safe, efficient operation.
In a town like Highland Park, word travels fast — and that is exactly how most of our customers find us. KIC Refrigeration has earned the trust of Highland Park property owners through years of delivering honest system evaluations, quality HVAC installations, and heating and cooling systems that keep families comfortable without inflated utility bills.
We believe the best advertising is a neighbor who stays comfortable all year. That is why every KIC Refrigeration project in Highland Park, TX is completed to the highest standard, backed by our workmanship warranty and manufacturer guarantees, and supported by a team that answers the phone when you call. Your trust is our most valuable asset.
What makes us different from every other heating and cooling company in the area.
If the repair does not solve the problem or the installation does not perform to specification, we come back and make it right at no additional cost. Our guarantee covers workmanship, parts, and system performance because half-finished work is not in our vocabulary.
Every technician carries EPA Section 608 Universal certification for refrigerant handling — required by federal law for working with R-410A, R-22, R-32, and all regulated refrigerants. Your system is serviced by technicians who handle refrigerants legally and responsibly.
You receive a written estimate with itemized parts and labor costs before any work begins, and the final invoice matches. No diagnostic fees hidden in the repair bill, no surprise surcharges — just honest pricing you can verify and trust.
We help you select equipment with the highest SEER2, HSPF2, and AFUE ratings that fit your budget, and we install it to manufacturer specifications so you actually achieve rated efficiency. Proper charge, proper airflow, proper duct sealing — the details that turn rated efficiency into real savings.
We carry full general liability and workers compensation coverage on every job. Our HVAC license is current in every state we operate, and we pull permits when local codes require them. Your property and our crew are fully protected on every visit.
Get the information you need to make confident HVAC decisions for your property.
The ideal time for HVAC replacement in Highland Park is during the shoulder seasons — spring and fall — when demand is lower, equipment availability is highest, and scheduling is more flexible. Contractors are less booked during these periods, which means faster installation timelines and potentially more competitive pricing. You are also more likely to find manufacturer rebates, utility incentive programs, and promotional financing during off-peak months. From a technical standpoint, moderate temperatures allow your new system to be commissioned and tested under less extreme conditions. However, KIC Refrigeration completes HVAC installations year-round in Texas and can often start within days of your approved estimate, even during peak summer or winter demand. If your current system is showing signs of failure, do not wait for the perfect season — a planned replacement is always better than an emergency one.
HVAC repair costs in Highland Park typically range from $150 to $500 for minor fixes such as capacitor replacement, contactor swaps, or thermostat wiring issues. Mid-range repairs like blower motor replacement or refrigerant recharging run $500 to $1,200. Major repairs — including compressor replacement, heat exchanger repair, or evaporator coil swap — cost $1,200 to $2,500 or more depending on equipment brand and system type. The final price depends on whether you have a furnace, heat pump, air conditioner, boiler, or ductless mini split, as parts and labor vary significantly between system types. Our NATE-certified technicians diagnose the issue accurately on the first visit, and KIC Refrigeration provides a written estimate with transparent pricing before any work begins. We never charge a diagnostic fee when you proceed with the recommended repair.
KIC Refrigeration installs and services all major HVAC equipment manufacturers in Highland Park including Carrier, Lennox, Trane, Daikin, Goodman, Rheem, York, Bryant, American Standard, Mitsubishi, and Fujitsu. For ductless mini split systems, we specialize in Mitsubishi, Daikin, and Fujitsu units which are the market leaders in inverter-driven technology. We are not locked into a single manufacturer or distributor, which means our recommendations are based entirely on what best fits your home size, budget, efficiency goals, and existing infrastructure. Each brand offers different warranty structures, SEER2 ratings, and feature sets — from basic single-stage units to premium variable-speed communicating systems. Our NATE-certified technicians install every unit strictly to manufacturer specifications and register all warranties on your behalf.
Most residential HVAC installations in Highland Park, TX are completed in 1 to 3 days depending on the system type, condition of existing ductwork, and complexity of the project. A straightforward furnace and air conditioner replacement on existing ductwork typically takes a single day — our crews arrive in the morning and commission the new system by afternoon. Heat pump conversions, ductless multi-zone installations with line sets routed through walls, and projects requiring new or modified ductwork may take 2 to 3 days. Commercial installations and whole-building systems can extend to a week. We schedule around your availability, coordinate all permits and inspections, and protect your flooring and walls throughout the process. Every installation concludes with a full system commissioning including airflow verification and refrigerant charge confirmation.
Heat pumps offer both heating and cooling from a single outdoor unit, making them significantly more energy-efficient than furnaces for moderate climates. A heat pump does not generate heat — it transfers it from outdoor air, which requires far less energy than burning gas or running electric resistance coils. Modern cold-climate heat pumps with variable-speed inverter compressors operate effectively down to minus 15 degrees Fahrenheit, making them viable in most Texas locations. For Highland Park homeowners with natural gas access, a dual-fuel system — heat pump for primary heating paired with a gas furnace for backup during extreme cold — often provides the best balance of efficiency and performance. Heat pumps also qualify for federal tax credits under the Inflation Reduction Act. KIC Refrigeration evaluates your specific climate zone, insulation levels, and utility rates to determine whether a heat pump, furnace, or dual-fuel system is the smartest investment.
Most HVAC installations, major equipment replacements, and significant ductwork modifications in Highland Park require a mechanical permit from the local building department. This applies to furnace and air conditioner replacements, heat pump installations, boiler swaps, and new ductless mini split systems. Minor repairs like part replacements and refrigerant recharges typically do not require permits. KIC Refrigeration handles all permitting, code compliance documentation, and scheduling of final inspections on your behalf — you do not need to visit any government office or coordinate with inspectors. Permits exist to ensure your system is installed safely and to code, which protects your home and preserves your equipment warranty. Unpermitted work can create liability issues and complicate future home sales. We ensure every project meets current Texas mechanical codes and International Mechanical Code standards.
Thousands of satisfied customers — here is what a few of them had to say.
"KIC Refrigeration replaced our old window units with a mini split system. Night and day difference in comfort and noise level. Wish we had done it sooner."
"AC repair was fast and fairly priced. The compressor was failing and they had the part on the truck. Done in about ninety minutes."
"Good experience with the furnace tune-up. Technician was thorough and pointed out a couple things to watch for. Only reason for four stars is scheduling took a few days."
Professional heating and cooling services extending to neighboring cities and towns.